Thermomètre LCD 105410

Arrêt automatique au bout d'une heure

Sonde de capteur en acier inoxydable de 133 mm avec cable caché 1m

Capuchon de protection en plastique pour sonde

Avec support sur l'unité arrière et compartiment pour câbles de capteur

Rappel de mémoire MAX / MIN (° F / ° C)

Bip d'alarme pour limite haut ou limite bas

Unité de température sélectionnable °F / °C 

DATA HOLD / Fonction de test sélectionnable

Indicateur de batterie faible

Temps de détection de température: moins d'une seconde

Gamme de mesure:

-50°C ~ + 300°C 

Résolution: 0,1 °C

Précision:

± 1 °C dans la plage de -30°C ~ + 150°C

± 1,8 ° F Dans la plage de -22 ° F ~ + 302 ° F

Température ambiante pour boîtier en plastique:

-10°C ~ + 50°C

Pile: 1 X 1.5V "" A76 "" Taille (LR44, G13) ou équivalent fournie dans la boite

• Installation
  • Unpack The Thermometer With Care.
  • Open The Battery Door. Then Fully Extend The Probe Cable. Install One ＂A76＂ Size (Or Equivalent) Battery Into The Battery Compartment And Close The Battery Door.
  • Take Off The Probe Cap From The Probe Tip, The Thermometer Is Now Ready For Use.
  • Replace New Battery When The Low Battery Indicator Appears On The Screen.
• Operation:
  • Press the ＂on/off＂ button. All functions will show on the display. The thermometer is ready for use.
  • Press the ＂°c/°f＂ button to select desired temperature unit. It will change immediately.
  • Press the ＂hold/test＂ button to ＂test＂ position for temperature measurement or ＂hold＂ position to retain reading for recording. The word ＂hold＂ will flash on the display to indicate the holding position.
  • Press the ＂max / min＂ button. ＂min＂ sign will be shown. The minimum temperature tested will display. Press the button again. ＂max＂ sign will be shown. The maximum temperature tested will display. It will go back to the testing position automatically after three seconds.
• Temperature Alarm Setting:
  • Press and hold the ＂low alarm＂ or ＂hi alarm＂ button for setting alarm at desired minimum or maximum temperature limit. The dis play will show -50°c or -58°f and start to
  • increase up to +150°c or +302°f / +299°c or +570°f depending on the available measurementrange.
  • Release the ＂low alarm＂ or ＂hi alarm＂ button when the desired temperature isapproached. The display value will stop increasing.
  • After releasing the button for approximately 3 seconds the thermometer will return to the testing mode. ＂lo＂ or/and ＂hi＂ sign will display. The alarm will sound 4 beeps per minute when the measured temperature equals or is greater than the maximum temperature or
  • less than the minimum set value.
  • To stop beeping, press any button.
  • To delete the alarm set, press ＂°c/°f＂ or ＂on/off＂ button.
• Precautions:
  • To obtain the best results, the probe tip should be immersed at least 10mm. Into the tested substance.
  • Remove the battery from the battery compartment if the thermometer will not be used for long duration of time or during storage.
  • The thermometer cannot be used or put inside any oven or microwave.